Door & Panel
All Units are available in 3 finishes and two heights 76″ and 80″ and widths from 36″ to 60″ in 1/4″ increments.
- Brushed Nickel
- Matte Black
This shower door offers a true frameless appearance featuring expanses of clear tempered glass and minimal hardware with no clutter from headers or adjustment channels. The door open in both directions on heavy-duty brass hinges and the in-line panel is supported by three low profile clips.
- 8” Deluxe Pull Handles
- 2 Heavy Duty Hinges
- 2 Wall Mount Clips
- 1 Floor Mount Clip
- Acrylic Drip Rail Acrylic Dam Strip
- 3/8” Tempered Glass Door – note the door is ½” shorter than the panel
- 3/8” Tempered Glass Panel
- For the exact size of your door and panel based on unit width click here
- Easy-clean enduro shield coating is factory applied to both the interior and exterior surfaces of the glass
- Deluxe Heavy Duty Hardware is solid brass and plated to match plumbing fixtures and other decorator items.
- All units include a clear acrylic drip rail and optional clear dam strip for maximum waterproofing
- Available in two heights 76″ and 80″ and widths from 36″ to 60″ in 1/4″ increments
- Product Type: Shower door
- Frame Type: Frameless
- Door Opening: Hinged
- Glass Texture: Clear
- All units are completely reversible (Photo –Door / Panel & Panel / Door
Measuring, Installation & Assembly
Tools Needed for Installation
Absolutely Not! Measurements must be based on the finished opening.
If the fiberglass or acrylic has a radius in the corners between the horizontal curb and the vertical walls where the unit will attach – you will not be able to install this unit. Also, if the walls where the unit will attach are not reinforced with structural material such as a wooden stud which the unit may be attached to – you will not be able to install this unit.
You should check your walls for plumb using a level and a straight piece of wood equal to the height of your unit (76” or 80”).
For the wall where your door will install:
If the wall leans in or out by no more than ¼” you will be able to compensate by varying the overlap of the hinge to the door. If the wall leans in or out by more than ¼” you will not be able to install these stock doors and you should check locally for a custom door.
For the wall where your panel will install:
If the wall leans out up to 3/8” you will be able to compensate by adjusting the width of the caulk joint between the panel and the wall.
If the wall leans out more than 3/8” you will need to order the optional Caulk Adaptor. On the Retailer’s site search for “Caulking Adaptor” and add the abbreviation for your finish. For example “ Caulking Adaptor MB” for Matte Black; “Caulking Adaptor CH” for Chrome and “Caulking Adaptor BN” for Brushed Nickel. Installation instructions are included with the adaptor.
If the wall leans in up to 3/8” you will be able to compensate by adjusting the width of the caulk joint between the panel and the wall. However since this wall condition reduces the space available to install the unit, you should adjust your width. For example, if you measure 46-1/2” at the curb and your wall leans in by 1/4”, you should order your unit based on a revised measurement of 46-1/4”.
If the wall leans in more than 3/8” you will need to order the optional Caulk Adaptor as detailed above. You will also need to adjust your width as described above. For example, if you measure 46-1/2” at the curb and your wall leans in by 3/4”, you should order your unit based on a revised measurement of 45-3/4”.
Due to the weight of the glass panels, you will need two people to install your unit.
You will need the following:
- Flat Blade screwdriver
- Phillips screwdriver
- A “Screw Gun” with a #2 Phillips Bit
- Drill with ¼” bits appropriate for your wall type (check with your hardware store)
- Razor Knife
- Measuring Tape
- Wooden Shims (available at your hardware store)
- Caulking gun and a tube of clear silicone
For more details reference the .pdf instructions on the Overstock.com site. A printed copy of the instructions is also included with each unit.
The door swings in and out. However, for safety reasons and to meet building codes, the out-swing of the door must not be blocked by a toilet, sink, wall, etc.
The drip rail presses on the bottom of the door and fills the ½” gap between the bottom of the door and the curb. The “deflector” protrudes to the interior and helps divert water running down the door into the shower. The flexible “wiper blade” keeps water from passing under the door. If the curb does not have a slight slope to the interior the optional “dam strip” should be applied.
Generally, no. The 76” or 80” height is not intended to be installed on top of a tub. And in the case of steel or porcelain tubs, you cannot screw the bottom clip to the tub without damaging the surface.
All glass has a slight greenish tint due to the presence of iron in the raw materials.
No, the Caulk Adaptor must be ordered separately. Order:
- Caulking Adaptor BN if your finish is Brushed Nickel
- Caulking Adaptor MB if your finish is Matte Black
- Caulking Adaptor CH if your finish is Chrome
Relative to the 1/8” gap between the door and the panel. ..In most cases, the shower spray is directed across the 1/8” gap, not into the gap, and little to no water will pass thru the gap and onto the floor*. In smaller showers, homes with extremely high water pressure or installations with multiple shower heads this may be a problem and can be corrected with the Acrylic Strike described below.
Relative to the 5/16” gap between the glass and the wall where the hinges are installed…. Most units are installed with the hinge side of the door closest to the shower head. In this case the shower spray does not spray directly into this area and leakage is unlikely*. If the door hinges from the opposite wall, the spray will go across the gap, not into the gap and leakage is unlikely*.
- Please note that frameless units are designed for a clean site line of clear glass with minimal amounts of hardware covering the glass. With these design elements, frameless units are not waterproof and some minor leakage is inherent to the design. The units can be made more waterproof by adding the Acrylic Strike described below but this interrupts the clean appearance of the unit.
The acrylic strike is optional and may be ordered by searching for “Acrylic Strike”. The strike is a clear polycarbonate that presses over the edge of the fixed panel and the door closes against it. Some homeowners prefer this to keep the door from swinging into the shower. The strike also includes a soft acrylic blade that seals against the door and helps prevent water from penetrating the 1/8” gap between the door and the panel. Use is optional and the need for this part varies with the design of the shower. If the shower is small or if the shower spray is directed at the gap between the door and the panel the Acrylic Strike is an appropriate addition to the unit.
The 3/8” tempered glass used in Symphony Hinged Frameless Doors is very heavy. A typical door weighs in excess of 70 pounds. The glass and the glass panel are packaged in separate boxes with multiple layers of protection. Since these products can only be shipped and delivered by commercial freight carriers, the outer cardboard layer may be scuffed, slightly torn, etc. in transit. If the door and/or panel is not damaged there is no need to replace the unit.
Important Information to Review Before you Order your Symphony door:
Our product is designed to provide the optimum appearance of a true “frameless” shower door. The hinge and clip system provide structural support for the enclosure while maintaining a clean, uncluttered appearance. Many competitors install their fixed panels in deep extruded aluminum channels to provide adjustability and “stretch” their size offering. We achieve the same objective by offering units in ¼” increments to provide a custom fit with a stock product. However this approach makes accurate measurements, including checking walls for plumb, a key to a successful installation. Measurements should only be made on your finished opening. Do not measure unfinished, stud-to-stud openings and attempt to adjust for the thickness of the tile, granite, etc. Also, this unit cannot be installed on Fiberglass or Acrylic stalls.